How to Remove and Replace a Drain Stopper

Download Article

Learn to install a sink stopper replacement with this easy DIY guide

Co-authored by James Schuelke and Amy Bobinger, BA

Last Updated: October 20, 2025 Fact Checked

Download Article

• Removing the Old Stopper
|
• Disconnecting the Drain
|
• Installing the New Drain
|
• Assembling the New Stopper
|
• Video
|
• Things You'll Need

|Show more |Show less

It's time to replace your sink stopper—but with all the parts and pieces around and below your sink drain, you aren't completely sure how to get started. As far as home repairs go, replacing a pop-up sink stopper is pretty low on the difficulty curve, and we're here to walk you through everything you need to know. We talked to professional plumbers David Balkan and James Schuelke to learn exactly how to remove the old stopper, disconnect and install a new drain, and install your new stopper. In no time at all, your sink stopper will be ready to go!

Changing a Sink Plug

Professional plumber James Schuelke says to look under the sink to find the drain stopper assembly. Here’s how to replace it:

1. Unscrew the pivot nut by hand and pull it out with the pivot rod.
2. Undo the screw that connects the extension bar and the lift rod.
3. Lift out the pop-up drain stopper with your fingers or a flathead screwdriver.
4. Disconnect the P-trap and remove the sink stopper's drain pipe.
5. Take each piece to the hardware store and find replacements.
6. Reassemble the sink drain pipe and the new stopper.

Steps

Section 1 of 4:

Removing the Old Stopper

Download Article

1. 
   1
   Undo the clamp that connects the pivot rod and extension bar. Schuelke says to find the stopper mechanism, look for a U-shaped clip (called a clevis) with a bar that goes inside the tailpiece of the stopper. The vertical metal bar, called an extension bar, has a series of holes in it. It’s connected to a rod that enters the sink's drainpipe (called the pivot rod). Pinch the V-shaped spring clamp that holds them together to disconnect them.

   • Keep all the pieces you disconnect in case you need to use them again.
   • If you can’t find the extension bar, it may have snapped off due to corrosion.
   • If the spring clamp is broken, replace it with a new one designed for your faucet brand.
   • If you have a pull-out stopper, you may be able to pull it straight out without having to disassemble anything. In this case, you likely will not see an extension bar under the sink.
   • If you have a pedestal sink, you may need to move the sink away from the wall to access the stopper assembly. Use an adjustable wrench to disconnect the water lines so you can move the sink.

   Meet the wikiHow Experts

   James Schuelke is a licensed plumber with over 30 years of experience. He co-owns Twin Home Experts, which operates in Los Angeles, Phoenix, and the Pacific Northwest.

   David Balkan is a professional plumber and the Committee Chairman of the Masters Plumbers Council. He is also the CEO of Balkan Sewer and Water Main Service and President of Balkan Sewer and Drain Cleaning.
2. 
   2
   Unscrew the pivot nut and pull it out along with the pivot rod. The pivot nut is threaded onto a short stub on the drainpipe under the sink. It’s where the pivot rod connects to the drain. Turn the nut counterclockwise by hand (or use a plumbing wrench if necessary) to remove it. Pull it straight off along with the inserted pivot rod.

   • If there’s anything under the sink, clear it out so you have room to work.
   Advertisement
3. 
   3
   Undo the screw connecting the lift rod if you’re replacing it. The lift rod and extension bar are connected behind the sink via a U-shaped joint, or clevis. Undo the screw on the clevis if you plan to remove the lift rod, then pull the lift rod out of the sink.

   • If there’s nothing wrong with your lift rod, it’s fine to leave it in place and re-use it.
4. 
   4
   Lift out the pop-up drain stopper in the middle of your sink. The stopper is no longer connected to anything, so pull it up out of the sink by hand. Use your fingernails or a flathead screwdriver to pry it up out of the drain.

   • If you have a lift-and-turn drain stopper: Adjust the drain stopper so the drain is completely closed. Then, twist the drain stopper counterclockwise (without twisting off the top cap) to remove it from the drain.
   • If you have a flip-it drain stopper: Slide a flathead screwdriver underneath one of the legs of the stopper that's resting on the drain. Then, gently pry one end up and remove it from the drain.
5. 
   5
   Clean the drain stopper if you plan on reusing it. Fill a bowl with white vinegar and let the drain stopper soak for 30 minutes. If necessary, scrub it down with an old toothbrush. Once it's done soaking, rinse it off with clean water.

   • For an especially effective clean, wash your old sink stopper with equal parts baking soda and vinegar. Just be mindful of the mess!
   • You can also soak your sink stopper in a mixture of sudsy water and dish soap.
6. 
   6
   Purchase replacement for your drain stopper assembly. Look online for a replacement sink stopper assembly kit or take everything you've disconnected to a home improvement store. If you have details on the brand and model, all the better. Buy a replacement kit that’ll fit the opening in your sink. If you can't find a kit that fits your pipe or you'd rather replace the whole mechanism, disconnect the drain pipe (described in the next section) and bring that with you, too.

   • If you're only replacing the stopper mechanism components, skip down to the section on installing the new stopper assembly.
   • You don’t have to take the drain out so long as it appears to be in good working order and your replacement kit matches the opening of the sink. However, you may want to replace the whole thing if it’s especially old or you can’t find a kit that fits the sink’s collar.
Advertisement

Section 2 of 4:

Disconnecting the Drain

Download Article

1. 
   1
   Undo the connection between the P-trap and the drain pipe. Then, turn the nut connecting the drain pipe that leads up into the sink and the P-trap (the U-shaped pipe). According to Balkan, you’ll typically only need channel locks or a pair of pipe wrenches to disconnect a sink drain. If the drain installed in the last 10 years, “it will unscrew and screw right back together again,” says Balkan—but he cautions that older drains may be more difficult to remove.

   • Before you get started, put a bucket under the drain pipe and lay some towels down. Also, shut off the water—”every sink has its own shutoff valve” under the sink, says Balkan.The P-trap holds water, so having the bucket in place will help prevent spills.
   • Avoid using too much force on the pipes, Balkan cautions. “They’re typically not thick gauge, high-quality plumbing fittings because it’s a sink drain. You have to be careful how you handle them [or] they can crumble or break.”
   • If you want to be extra cautious, carefully disconnect the other end of the trap where it connects to the pipe leading into the wall.
2. 
   2
   Unthread the sink stopper's drain pipe from the underside of the drain. Now that the bottom of the drain pipe is free from the P-trap, loosen the nut that connects it to the threaded bottom of the sink drain. Loosen the nut by hand, or use a wrench if you can’t get the nut loose.
3. 
   3
   Push up on the sink drain and pull it out of the sink basin. Your drain is now free, but there’s probably plumber’s putty sticking the sink to the opening. Just push and jiggle the drain pipe free to get it off of the putty. If it still won't budge, a few taps from below with a rubber mallet should do the trick.

   • Clear away the old putty residue in the sink bowl with a plastic putty knife and a wet rag.
   • If the drain won’t come out, try loosening the locknut as described in the next step.
4. 
   4
   Loosen the locknut that holds the drain in place. Most sink drains have a compression nut between the drain's lip on the topside of the sink and a locknut on the underside. The locknut will be snug up against the underside of the sink. Use a large wrench or channel locks to loosen and remove it.

   • If the whole sink drain spins when you try to turn the locknut, hold the drain pipe with one hand while twisting with the other.
   • Some sink drain locknuts have screws that need to be removed first. Remove the screws and then pull off the housing to access the compression fitting.
5. 
   5
   Take everything to the hardware store to find a replacement kit. You don't have to replace the old sink stopper assembly with the exact same model so long as the diameter of the sink opening matches the stopper and pipe. The drain pipe must also match the diameter of the P-trap.

   • If your other pipes are PVC, get a PVC drain pipe kit.
   • If the pipes are metal, go with a metal kit.
   • Unless your setup is on the older side, the sink opening is probably 1.25 inches (3.2 cm) in diameter and the pipes will be 1.5 inches (3.8 cm).
Advertisement

Section 3 of 4:

Installing the New Drain

Download Article

1. 
   1
   Roll up some fresh plumber’s putty and put it around the basin opening. Take a small handful of plumber's putty from its container and work it around in your hands until it feels like soft clay. Then, roll it into a “snake” about the thickness of a pencil, and form a ring by pressing the ends together. Press this ring onto the rim of the opening in your sink basin.

   • Make sure you've removed any old putty from the sink with wet rags and a plastic putty knife first.
2. 
   2
   Push the new sink drain pipe into the opening and onto the putty. Press the new drain collar down from the top of the sink. Press firmly enough that the plumber's putty squeezes out around the top lip of the drain. Clear this excess putty away with your fingers and a wet rag.

   • Use as much pressure as necessary until the rim around the sink opening is flush with the basin around it.
   • Don’t be shy about pushing and pulling down on the pipe! It can take a fair bit of pressure. You won’t break anything.
3. 
   3
   Stack any included gaskets on the drainpipe locknut or bell housing. Follow your kit’s instructions here. To keep the sink watertight, install the required gaskets and nuts that firmly keep your drainpipe in place. Tighten everything firmly by hand unless instructed otherwise.
4. 
   4
   Tighten the locknut or bell housing nut to secure the drain in place. Use a large wrench or channel locks to tighten a traditional locknut. Make the connection snug, but don't try to over-tighten it or you may crack the porcelain sink basin. If you have a locknut with screws, just hand-tighten the locknut and use a screwdriver to secure the screws and make the compression connection snug.

   • If you have a bell washer strainer, slide the bell housing over the sink drain and wrench-tighten the nut that fits onto the exposed sink drain threads at the bottom.
5. 
   5
   Smear pipe joint compound onto the threads at the bottom of the pipe. Most sink stopper drain pipes only have a few rings of threads to attach them to the sink drain, which makes them prone to leaks. To prevent leaks, smear pipe joint compound around the bottom several threads of the sink drain.

   • You can also wrap Teflon tape around the threads, but pipe joint compound provides superior leak protection.
   • If your sink drain kit has a metal tailpipe, the exposed threads may be on the P-trap instead of the sink drain. If so, smear the pipe joint compound on the exposed P-trap threads instead.
6. 
   6
   Screw on the drain pipe with the cap opening pointing back. Hand-tighten the connection between the drain pipe and the sink drain until they're snug. Make sure the pipe stub (opening for the stopper) that will accept the pivot rod is pointing straight back to the wall.

   • Hold the pipe stub in place while tightening the nut—but do not over tighten the nut, or you could damage the new sink or the new drain assembly.
7. 
   7
   Connect the P-trap to the drain pipe to complete the connection. If your new sink stopper drain is the same length as the old one, the existing P-trap should reattach without much trouble. Gently align the pipes and slide them in together. Then, tighten the compression nut by hand.

   • If the pipe is too long, use a hacksaw or pipe cutter to trim off some of the pipe.
Advertisement

Section 4 of 4:

Assembling the New Stopper

Download Article

1. 
   1
   Align and place the pop-up drain stopper into the sink's drain opening. The drain stopper will have a notch in the bottom with a hole behind it. Line up the stopper so that the notch is facing directly toward the opening for the lift handle, which is usually directly behind the faucet spigot. Maintain this alignment as you insert the stopper into the drain opening.

   • If you're installing a lift-and-turn sink stopper: Center the stopper in the drain and twist the stopper clockwise.
   • If you're installing a flip-it sink stopper: Slide on the O-ring and gasket that comes with your new flip-it sink stopper. Then, rub a little petroleum jelly along the opening to the drain. Place your stopper directly into the drain, twisting it slightly to the right to hold it in place.
2. 
   2
   Insert the plastic washer on the horizontal stub on the drain pipe. Your kit will come with a small plastic ring that is slightly wider in diameter on one side than the other. Place the narrower side into the opening first. This washer will help hold the ball on the pivot rod in place and provide a watertight seal.

   • Check the installation instructions for any specifics, like whether the washer should be turned a certain way.
3. 
   3
   Put the pivot rod into the stub inside the drain stopper. Insert the rod into the opening on the drain pipe. Angle it so it goes into the hole on the bottom of the drain stopper. This can take a few tries, so don’t get discouraged if you don’t get it the first time.

   • You'll know you've succeeded if the drain stopper bobs up and down in the sink. Pull up on the stopper to verify the attachment — if you can't pull it out of the drain opening, then it's attached.
   • Some drain stoppers can be installed without being hooked onto the pivot rod. This allows them to be removed for easier cleaning.
4. 
   4
   Feed the pivot nut over the pivot rod and tighten it. Tighten the nut by hand onto the threads on the end of the drain pipe’s horizontal stub. If you overtighten the nut, the pivot rod may not be able to move up and down freely; test the rod's movement, and loosen the nut slightly if necessary.
5. 
   5
   Install and connect the lift handle and extension bar. Drop the lift handle into the opening in the faucet fixture or connect the lift bar to the lift handle with a clevis and a screw. You'll end up with a single vertical shaft, the bottom of which should line up with the horizontal pivot rod. Make sure the series of holes in the extension bar are facing the pivot rod.

   • Once the rod is connected, lifting the stopper behind the faucet will pull down on the stopper.
6. 
   6
   Connect the pivot rod to the extension bar with the spring clamp. Angle the pivot rod downward until the drain stopper pops up to its highest position in the sink basin. Feed the pivot rod through the corresponding hole in the extension bar. Use the V-shaped spring clamp that comes with the kit to hold the pivot rod and extension bar together.

   • Don’t tighten the clamp as hard as you can; just apply enough pressure to hold the rod and bar in place. This is the hardest part of the process—getting the rod and bar to the right height where the stopper will open and close correctly.
7. 
   7
   Test the stopper, make adjustments as needed, and check for leaks. Lift up on the lift handle and see if the drain stopper plugs the sink drain completely. Move the pivot rod up or down on the openings of the extension bar until it looks and feels right. Then, run water in the sink to ensure you’ve got a good seal.

   • Don’t get frustrated. It can be annoying trying to line the rod up at the right height, but you will eventually get it right.
   • Once you’ve got the rod configured right, tighten the clamp completely to close the connection.
8. 
   8
   Tighten everything fully and enjoy your new sink stopper. Check for leaks around the pivot nut and any other pipe connections you've made. Once everything looks good, give all of the washers and nuts one more full rotation to tighten everything all the way.
   EXPERT TIP

   

   James Schuelke

   Professional Plumber

   James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business plumbing experience and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest.

   

   James Schuelke
   Professional Plumber

   You can use this same mechanism later if you need to adjust your sink stopper. Use one hand to hold the stopper at the height you want it. Once it's adjusted, use the other hand to set the U-shaped clip in the extension bar, then screw the tailpiece nut back on to the pop-up assembly.
Advertisement

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Things You'll Need

• Sink stopper replacement kit
• Sink drain kit (optional)
• Pipe joint compound
• Plumber's putty
• Adjustable wrench or channel locks